DANGER GAS NO SMOKING

DANGER SIGNS are used where an immediate hazard situation exists and if not avoided, will result in DEATH or SERIOUS INJURY. Danger wording should not be considered for property damage accidents unless personal injury risk is present. All employees shall be instructed that DANGER SIGNS indicate immediate danger and that special precautions are necessary. OSHA 1910.145(c)(1)(ii). The sign should contain sufficient information to be easily understood. OSHA 1910.145(e)(2). Signs are .063 aluminum and reflective.

DANGER HARD HAT AREA

DANGER SIGNS are used where an immediate hazard situation exists and if not avoided, will result in DEATH or SERIOUS INJURY. Danger wording should not be considered for property damage accidents unless personal injury risk is present. All employees shall be instructed that DANGER SIGNS indicate immediate danger and that special precautions are necessary. OSHA 1910.145(c)(1)(ii). The sign should contain sufficient information to be easily understood. OSHA 1910.145(e)(2). Signs are .063 aluminum and reflective.

DANGER KEEP OUT SIGN

DANGER SIGNS are used where an immediate hazard situation exists and if not avoided, will result in DEATH or SERIOUS INJURY. Danger wording should not be considered for property damage accidents unless personal injury risk is present. All employees shall be instructed that DANGER SIGNS indicate immediate danger and that special precautions are necessary. OSHA 1910.145(c)(1)(ii). The sign should contain sufficient information to be easily understood. OSHA 1910.145(e)(2). Signs are .063 aluminum and reflective.

DANGER NO SMOKING SIGN

DANGER SIGNS are used where an immediate hazard situation exists and if not avoided, will result in DEATH or SERIOUS INJURY. Danger wording should not be considered for property damage accidents unless personal injury risk is present. All employees shall be instructed that DANGER SIGNS indicate immediate danger and that special precautions are necessary. OSHA 1910.145(c)(1)(ii). The sign should contain sufficient information to be easily understood. OSHA 1910.145(e)(2). Signs are .063 aluminum and reflective.

DANGER NO TRESPASSING

DANGER SIGNS are used where an immediate hazard situation exists and if not avoided, will result in DEATH or SERIOUS INJURY. Danger wording should not be considered for property damage accidents unless personal injury risk is present. All employees shall be instructed that DANGER SIGNS indicate immediate danger and that special precautions are necessary. OSHA 1910.145(c)(1)(ii). The sign should contain sufficient information to be easily understood. OSHA 1910.145(e)(2). Signs are .063 aluminum and reflective.

DANGER RESTRICTED AREA

DANGER SIGNS are used where an immediate hazard situation exists and if not avoided, will result in DEATH or SERIOUS INJURY. Danger wording should not be considered for property damage accidents unless personal injury risk is present. All employees shall be instructed that DANGER SIGNS indicate immediate danger and that special precautions are necessary. OSHA 1910.145(c)(1)(ii). The sign should contain sufficient information to be easily understood. OSHA 1910.145(e)(2). Signs are .063 aluminum and reflective.

DANGER TAPE 1000'

DANGER TAPE 300'

DAYTON B-16 3/4 X 6" STRAIGHT COIL LOOP INSERT

Although simple in design and fabrication, the B16 Straight Coil Loop Insert is highly efficient for lifting and handling precast concrete elements. Standard inserts are shown in the chart. Special inserts for use with larger diameter coil bolts, or with loops having longer lengths and of heavier wire can be furnished, if required, on special order

DAYTON B-18 3/4" X 6" FLARED COIL LOOP INSERT

The load carrying capacity of any cast-in-place concrete insert is largely dependent upon the ability of the insert to draw upon the tensile strength of the mass of concrete within which it is embedded. The B18 Single Flared Coil Loop Insert makes effective use of this principle by increasing the depth and width of concrete embedment. B18 inserts are available with an optional B3 Screw-on Coil for use with the B30 Screw-on Plastic Cone which acts to set the insert back from the face of the concrete. Minimum spacing between inserts is twice the corner distance.

DAYTON BAR

The A95 - Dayton Bar is manufactured with a 1” x 2” structural tube handle that has been carefully Mig welded to a heat-treated milled blade. This bar is an ideal tool for use by the tilt-up erector— you will find many uses for it, from adjusting and/or stripping side forms to “jockeying” tilt-up wall panels into position. Available with either a 3” or 5” wide blade. Please specify blade width when ordering.

DAYTON F - 42 3/4" LTT INSERT - NC THREADS

The Dayton Superior F-42 Loop Ferrule Insert is fabricated by welding a looped strut to a closed-end ferrule. F-42 insert is available in the sizes shown in the chart and is well suited for structural connections and the suspension of equipment, piping, etc. Minimum spacing between inserts is twice the minimum corner distance.

DAYTON F-42 1/2" LTT INSERT - NC THREADS

NON STOCK The Dayton Superior F-42 Loop Ferrule Insert is fabricated by welding a looped strut to a closed-end ferrule. F-42 insert is available in the sizes shown in the chart and is well suited for structural connections and the suspension of equipment, piping, etc. Minimum spacing between inserts is twice the minimum corner distance.

DAYTON F-42 3/8" LTT INSERTS - NC THREADS

The Dayton Superior F-42 Loop Ferrule Insert is fabricated by welding a looped strut to a closed-end ferrule. F-42 insert is available in the sizes shown in the chart and is well suited for structural connections and the suspension of equipment, piping, etc. Minimum spacing between inserts is twice the minimum corner distance.

DAYTON F-42 5/8" LTT INSERT - NC THREADS

The Dayton Superior F-42 Loop Ferrule Insert is fabricated by welding a looped strut to a closed-end ferrule. F-42 insert is available in the sizes shown in the chart and is well suited for structural connections and the suspension of equipment, piping, etc. Minimum spacing between inserts is twice the minimum corner distance.

DAYTON J-6 SURE-LIFT BOND BREAKER (55 GALLON)

Sure Lift™ with Dye J6D is a reactive and membrane forming bond breaker for use in tilt wall construction. Sure Lift™ with Dye J6D is a special formula of polymers and propriety ingredients designed to provide clean, easy lifting of tilt panels. Sure Lift™ with Dye J6D has a fugitive dye for ease of visual inspection during application and is also available without the dye upon special request.